Skip to main content

Show, type and lock the distances to every outlet and switch

The Electrical plan view measures every outlet and switch from the walls for you: a chain of numbers along each wall, to the centre of each device. Tap a number to type a new distance, or its padlock to lock it; a locked number between two devices ties them together.

6 minUpdated 2026-11-22

An electrician sets out boxes by measurement: "first outlet 1.2 m from the corner, the next 3 m on, the switch 15 cm from the door frame". A plan that only shows where the symbols are leaves them to scale it off the drawing, and a quote or an installation built from guesses goes wrong. Since November 20, 2026 RoomSketch3D writes those numbers on the plan by itself.

Quick answer: open View & Layers (the stacked-sheets button, first in the toolbar) and tap the Electrical plan view. Along every wall face that has outlets or switches you now see a chain of dimensions: from the wall to the first device, from device to device, and from the last device to the next wall, all measured to the centre of each device. Tap any number to type a new distance (the device moves), or tap the padlock beside it to lock it. To print them, export with the Electrical plan view or tick Device distances in the export dialog.

This page explains what the numbers measure, how typing and locking work, and how to use the chain to check outlet spacing against the code. For everything else electrical, see electrical floor plan guide.

What you'll need

  • •A plan with outlets or switches on its walls (see Draw an electrical plan)
  • •Any device: the chain and its numbers work with a mouse or a finger

Step by step

  1. 1

    Turn the distances on

    The distances are a layer called Device distances. Two ways to show it: - Tap the Electrical plan view at the top of View & Layers. It shows exactly the electrician's layers: exterior dimensions, room labels, outlets, switches & symbols, circuit lines and device distances, with the furniture and room colors hidden. - Tick the Device distances row in any view. It sits under Furniture & electrical, indented below Show outlets, switches & symbols, next to Circuit lines. The menu then reads Custom mix · matches no view, which is fine; Save as view keeps that mix under your own name. The chains need the devices themselves to be shown: with Show outlets, switches & symbols off, the distances hide too. Plans that were saved in the old Electrical plan view before this layer existed open with the distances on.

    Device distances: on in the Electrical plan view, and a row of its own in any view.
  2. 2

    Read a wall's chain

    Each wall face with outlets or switches gets one chain, drawn just past the device symbols, with a thin leader from each device to the line:

    NumberMeasures
    FirstFrom the wall (a corner, or a wall meeting this one) to the centre of the first device
    MiddleFrom the centre of one device to the centre of the next
    LastFrom the centre of the last device to the next wall

    - Centre, not edge. The centre is the small triangle on the wall that marks each outlet, switch or combination. Electricians set out boxes to their centre, and the card's Along wall boxes now measure the same way, so the chain and a selected device's numbers always agree. - Wall to wall. A chain runs between the nearest corner or meeting wall on each side. Doors and windows don't cut it, so a switch beside a door is measured from the wall corner, not from the door frame. - One point per spot. A combination (a switch over a socket, a double outlet) is one point in the chain, at its triangle. - Units follow your settings: feet and inches or inches only, metres and centimetres or centimetres only, with a decimal point or a decimal comma (Settings → Measurements & Defaults). - Numbers show only where they fit. On a short or crowded wall zoom in to see them all.

    Wall → device → device → …, to the centre of each device.
  3. 3

    Type a distance to move a device

    Tap a number. A small box opens on the plan with the number in it (with a mouse, click it). Type the distance you want and press Enter: - An end number moves that end's device, so it sits exactly that far from the wall. - A middle number moves one device of the pair and leaves the other where it is. Which one moves depends on the direction the wall was drawn in, not on left or right on screen, so if one of the two must not move, lock its distance from the wall first. The box has a feet and an inches field (or metres and centimetres), a ✓ to apply, a × to cancel and the padlock. After a typed move the device is selected, so its own two distances show instead of the chain; tap empty space to see the whole chain again. Typing is the same move as dragging the device there, so every rule still applies: the device stays on its wall, can't land on a door or window, and respects any lock. If the distance can't be kept you see That distance doesn't fit on this wall. and nothing moves. Undo puts a typed move back. Worked example: a 14 ft living-room wall with outlets at 3 ft and 11 ft from the left corner shows 3', 8' and 3'. Type 6' in the middle number and one outlet moves so they are 6 ft apart: if the right one moves, the chain reads 3', 6', 5'. In the screenshot, 8' was typed between the two sofa outlets in place of 9' 4.03".

    Tap a number: type the distance, or lock it.
  4. 4

    Lock a distance, or tie two devices together

    The box that opens on a number has a padlock. Tap it to lock that number as it is now; tap it again to unlock. A locked number shows a small padlock on the plan.

    You lockWhat it does
    An end numberThe device's distance from that wall is locked: the same lock as the padlock next to its card's Along wall box. The device keeps the distance when the wall changes, and dragging or typing it is refused until you unlock it
    A middle numberThe two devices are tied: move one and the other follows at the same distance. A change that can't keep the distance (the other device wouldn't fit, or would land on a door) is refused

    A locked number is shown, not typed, and so are the numbers of a device whose wall distance is locked. A tie goes away when either device is deleted, and a pasted copy of a tied device isn't tied. Use ties for things that must stay together, like the two outlets either side of a bed or a desk.

    Top: padlocks on the chain, two outlets tied 8 ft apart and the last one locked to the wall. Bottom: a locked number opens read-only, with only its padlock.
  5. 5

    Interior walls: each face has its own chain

    An interior wall has two faces, and each face's outlets and switches are measured along that face only. A wall that meets the other side doesn't cut this side's chain, so the bedroom outlets on one face and the hallway switch on the other each get their own numbers. An outlet on the outside face of an outer wall is measured along the outside and ignores walls inside the house. To move a device to the other face, drag it across the wall (the face it will land on lights up blue). Its numbers then join the other face's chain. While you drag or place a device, the chain steps aside and the device shows two preview numbers. On an interior wall these preview numbers can differ from the chain you see after you let go; trust the chain once the device is dropped.

    Two faces, two chains: bedroom side on the left, bathroom side on the right.
  6. 6

    Selected devices and the card's Along wall boxes

    When you select an outlet or switch (or any door, window or wall piece), the chains step aside and the selected device shows its own two distances, which are the same numbers as its card's Along wall boxes (← → or ↑ ↓). They measure to the device's centre too. Tap elsewhere and the chains come back. This keeps the plan readable while you work on one device.

  7. 7

    Print and export the distances

    Open Export / Print / Share → PNG/JPG/PDF or Print. Tapping the Electrical plan view at the top ticks Device distances (Distances along each wall to outlets and switches) along with the electrical symbols, circuit lines and the symbol legend; in any other view you can tick it yourself. It is greyed out while Electrical symbols is unticked, because there is nothing to measure. The dialog is meant to open on the view your plan shows; if no view button is lit when it opens, tap Electrical plan so the options match the electrician's sheet. The chains print on PNG, JPG, PDF and Print (checked on a real PNG export). The DXF (CAD) export doesn't include them; dimension in your CAD program, or send the PDF with the DXF.

    Device distances in the export options, ticked by the Electrical plan view.
  8. 8

    Check outlet spacing with the chain

    The chain is the quickest way to check a plan against the spacing rules most US plans are checked against (2021 IRC Chapter 39, which follows NEC 210.52):

    WhereRuleRead on the chain
    Walls in living areasNo point along the floor line more than 6 ft from an outletEvery middle number 12 ft or less, each end number 6 ft or less (walls 2 ft or wider count)
    Kitchen counterNo point along the wall line more than 24 in from an outletMiddle numbers along the counter 4 ft or less, ends 2 ft or less
    BathroomAn outlet within 36 in of each basin's outside edgeMeasure from the basin edge with the tape measure; the chain runs wall to wall

    Because the chain measures wall to wall and ignores doors, subtract a door's width yourself where a doorway breaks the wall space (the code measures wall space along the floor line, which a doorway interrupts). These are code minimums; local amendments vary, and your electrician and building department have the final word. In Germany, DIN 18015-3 sets installation zones beside doors, windows and corners (10–30 cm); check the end numbers against them.

Tips

Lock the set-out points first

Lock the end number of the devices the electrician measures from (the switch by the door, the outlet centred on a bed wall), then type the others relative to them.

Tie pairs that belong together

Lock the middle number between the outlets either side of a bed or a desk: moving one moves both, so they stay symmetrical.

Zoom in on a busy wall

Numbers only draw where they fit. A short wall with three devices may hide one until you zoom in.

Use the view for checking, a saved view for working

If you want the distances while furnishing, tick Device distances in the Floor plan view and tap Save as view: your own view keeps both.

Common mistakes

Reading the numbers to the edge of the plate

Every number goes to the centre of the device (the triangle on the wall). To the plate's edge is half the plate width less.

Expecting a door to split the chain

The chain runs between walls; doors and windows don't cut it. A switch 6 in from a door frame shows its distance from the wall corner.

Trying to type a locked number

A locked number, or any number of a device whose wall distance is locked, is shown but not typed. Tap the padlock to unlock first.

Hiding the devices and losing the distances

The chains need Show outlets, switches & symbols on. Tick it again and they're back.

Trusting the numbers while dragging

On an interior wall the two numbers shown while you drag can differ from the chain after you drop. Read the chain once the device is down.

Frequently asked questions

How do I show the distance from the wall to each outlet?

Tap the Electrical plan view in View & Layers, or tick View & Layers → Device distances in any view. Every wall with outlets or switches then shows a chain of distances, to the centre of each device.

Can I dimension the distance between two outlets?

Yes, it is already there: the middle numbers of a wall's chain are centre-to-centre distances between neighbouring devices. Tap one to type a new distance; one of the two moves (lock the other's wall distance first if it must stay).

Are the distances to the centre or the edge of the outlet?

To the centre, marked by the small triangle on the wall. The card's Along wall boxes measure to the centre too (since November 20, 2026).

Why can't I type a number?

It is locked (it shows a padlock), or the device it moves has a locked wall distance. Tap the padlock to unlock it, then type.

It says "That distance doesn't fit on this wall". What now?

The device can't sit at that distance: it would run past the next wall, land on a door or window, or break a lock. Try a smaller number, move the thing in the way, or unlock.

Do the distances print?

Yes, on PNG, JPG, PDF and Print when Device distances is ticked in the export dialog (the Electrical plan view ticks it). They are not in the DXF export.

Can I measure from a door frame instead of the corner?

Not in the chain: it runs wall to wall. Use the tape measure for a one-off measurement, or note the door offset in the device's name.

Why don't I see the chain while an outlet is selected?

The chains step aside while a wall piece is selected, dragged or placed; the selected device shows its own two distances instead. Tap empty space and the chains come back.

Do my old plans change?

No. The distances are drawn from where the devices already are; nothing is moved until you type a number or drag a device. Locks you set earlier keep working.

Sources

Start designing your room

Put this into practice in the floor planner: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android