Skip to main content

Put outlets and switches together: multi-gang frames and switch-and-socket combinations

Several outlets or switches at one spot on the wall become one combination: drag one onto another (or tap Add outlet / Add switch), choose Side by side or Stacked, and give each device its own kind, name and height.

6 minUpdated 2026-11-16

Electricians rarely put one lonely device on a wall. By an entry door there are two or three switches in one frame; behind a TV or over a desk, a double or triple outlet; in a German plan, a light switch with a socket right under it. Since November 2026 RoomSketch3D draws these as combinations: one spot on the wall holding up to 5 outlets and switches, each with its own kind, name and height, drawn as their own symbols inside a thin frame.

A combination moves, flips sides and deletes as one, but every device in it counts on its own in the symbol legend and circuit list, and a circuit line can end on any one of them. This page walks through making one, both ways, and every setting. The full electrical workflow is in electrical floor plan guide.

What you'll need

  • •A plan with at least one outlet or switch on a wall (see Draw an electrical plan)

Step by step

  1. 1

    Select a device and tap Add switch (or Add outlet)

    Tap an outlet or switch on the plan. Its settings card has Add outlet and Add switch under the kind and Mount boxes, with the reminder Or drag one outlet or switch onto another to combine them. Tap one: the device becomes a combination of two, Side by side in one frame. The new one starts as a Duplex outlet or a Single switch (on a European device, an Earthed socket or a One-Way switch).

    Add outlet and Add switch sit under the kind and Mount boxes.
  2. 2

    Set each device's kind and name

    The card now lists one row per device: number · kind · name · Separate · Remove. Pick each device's kind from its drop-down (outlets and switches of the same pack). The first device's name is the card's main name box; the others have their own Name box. Names show on the plan under the frame, joined with a dot. The example is the switch by an apartment's front door: Switch (Single) for the entry light and Switch (Dimmer) named Living lights, both at Mount 3 ft 10 in (46 in to the bottom of the plates, about 48 in to their centre).

    Two rows, two kinds, one frame on the wall below.
  3. 3

    Or drag one device onto another

    Drag an outlet or switch along the wall onto another one. When it is right over the other symbol, a blue Drop to combine label appears on it. Let go and they become one combination. A device you place with +Add right on top of an existing one joins it the same way. The drop has to land on the other symbol: within about an inch along the wall (less when you are zoomed out). Two devices dropped next to each other stay two devices. Both must be on the same face of the same wall: a device on the other face (In / Out) never combines.

    Drop to combine appears when the drop will join.
  4. 4

    Different heights stack, equal heights sit side by side

    When you drag together two single devices at different heights, such as a switch at 46 in and an outlet at 12 in, the combination is Stacked and keeps both heights. At the same height they go Side by side. Switch any time with Layout → Side by side / Stacked: - Stacked: each row gets its own Mount. A device added with Add outlet / Add switch starts one frame (2.8 in, the 71 mm European pitch) below the lowest, or above it when that would go below the floor; type the height you need. - Side by side: one Mount for the frame; stacked heights are dropped and every device sits at the first device's height. On the plan a stacked combination is drawn outward from the wall, first device nearest the wall, because a plan can't show height. The 3D view shows the real heights.

    A switch dragged onto an outlet: Stacked, both heights kept.
  5. 5

    European frames: socket under the switch, triple sockets

    In the Europe pack the same steps make German-style combinations. A Schalter-Steckdosen-Kombination: a Switch (One-Way) with Add outlet, Stacked, gives an earthed socket one 71 mm frame below the switch. A worktop or desk frame: Socket (Earthed), Socket (Earthed) and Socket (USB) side by side. DIN 18015-3 recommends 105 cm (middle zone) or 30 cm (lower zone) above the finished floor; Mount is the bottom of the plate, so type about 101 cm or 26 cm.

    A three-gang European frame with one USB socket.
  6. 6

    How combinations look on the plan

    Each device draws its own symbol and tag, and a thin frame around them says "one box". From left: a US switch over a duplex outlet (stacked), a US three-gang switch (single, dimmer D, 3-way 3), a European one-way switch over an earthed socket, and a European triple socket with USB.

    Frames group the devices; each keeps its own symbol and tag.
  7. 7

    Separate a device or remove it

    Each row has two buttons. Separate (broken link) takes that device out and puts it on its own 6 in along the same wall, keeping its kind, name and height. Remove (red trash) deletes only that device; removing the first one makes the next the first, and its circuit lines stay connected. The trash can at the bottom of the card deletes the whole combination. Undo reverses any of these.

    Separate and Remove act on one row.
  8. 8

    Connect circuit lines to one device in the frame

    With the Circuit line tool, tap the device in the frame the run belongs to. In the example the dimmer of the front-door pair starts Breaker 3 to the living-room light, while the kitchen run Breaker 5 starts from the switch of the stacked kitchen combination. Each device in a combination is a separate stop, so one frame can sit on several circuits. See circuit lines.

    Breaker 3 starts at the dimmer; Breaker 5 at the kitchen switch.
  9. 9

    Check it in 3D and on the export

    In 3D a combination is one multi-gang plate or frame with a slot per device: side by side in a row, or one above the other at each device's height. On an Electrical plan export the legend counts every device separately and the circuit list names the device a line ends on. The DXF draws the devices of a combination side by side on the ELECTRICAL layer.

    Combinations in 3D: one multi-gang plate or frame, a slot per device.
  10. 10

    On a phone

    Tap the device; the settings fill the bottom of the screen with the same Layout buttons and device rows. Zoom in before dragging one device onto another. The kind list in each row is narrow on a phone, so a long kind name is cut short; tap it to see the whole list.

    Phone: Layout, rows, Add outlet / Add switch at the bottom.

Tips

Combination or single symbol?

If the box holds one part (a quad receptacle, a two-gang rocker), the single symbol is fine. Use a combination when the parts differ in kind, name, breaker or circuit line.

Name the parts that matter

Name the device that feeds something specific (Living lights, Breaker 12). Unnamed devices show only their symbol.

Up to five

Five devices is the largest common frame. For more, place two combinations next to each other.

Common mistakes

Expecting a near drop to combine

The drop must land on the other symbol. If Drop to combine didn't show, they stay separate; drag again, zoomed in.

Combining across the wall

Devices on opposite faces (In vs Out) of an interior wall serve different rooms and never combine. Flip one first if that's what you meant.

Typing the centre height into Mount

Mount is the bottom of each plate. Subtract half the plate height (about 2 in for a US plate, 4 cm for an 80 mm European frame).

Frequently asked questions

How do I show a light switch with an outlet below it?

Drag the outlet onto the switch (they keep both heights and stack), or select the switch, tap Add outlet and choose Stacked; then set each device's Mount.

How do I show a double outlet?

Select an outlet and tap Add outlet: two devices side by side in one frame. Or use the single Outlet (Quad) symbol if you don't need the halves apart.

How many devices can one combination hold?

Up to 5. Add outlet and Add switch are greyed out when it's full.

Can I mix outlets and switches in one combination?

Yes, any mix of outlets and switches from the same pack (US or Europe).

How do I split a combination again?

Tap Separate on a device's row: it moves 6 in along the wall as a device of its own. Or Undo right after combining.

Can lights or data jacks be part of a combination?

No, combinations are for outlets and switches. Place the other symbols next to the frame.

Sources

Start designing your room

Put this into practice in the floor planner: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android