Skip to main content

The complete guide to drawing an electrical plan in RoomSketch3D

One page for the whole job: which symbols exist, how outlets, switches, combinations and lights go on the plan, how to draw and route circuit lines, how to label breakers, what prints in each export, how to make a separate plan for each trade, the cable list with run lengths, and the placement rules (US code and German DIN) to check your plan against.

24 minUpdated 2026-11-16

An electrical plan is the drawing an electrician quotes and wires from: where every outlet and switch sits on the walls, where the lights, fans and detectors go on the ceiling, which switch runs which light, and which outlets share a breaker. RoomSketch3D draws all of that on top of your floor plan with standard symbols, and prints it as a clean sheet with a symbol legend and a circuit list.

This guide is the reference for all of it. It runs in the order you would build a plan: what the plan contains, the symbols, putting devices on walls and in rooms, the settings of each device, outlet and switch combinations, naming, circuit lines (drawing, routing along the walls, editing, styling), the settings card, right-click shortcuts, the legend and circuit list, exports, separate plans per trade (electrician, symbols only, furniture), the cable list with the length of every run, the 3D view, the rules to check your layout against (US code and German DIN 18015-3), shortcuts, and what the app can't do yet with the workaround for each.

Quick answer: open Symbols (the tab after Indoor and Outdoor, or the Symbols pill on a phone), tap an outlet or switch tile, tap +Add and tap a wall. Drop lights with +Add and drag them into place. Drag one outlet or switch onto another to make a combination. Tap Circuit line, tap the devices in wiring order (tap empty space to bend the line along a wall), press Enter. Then Export / Print / Share → PNG/JPG/PDF or Print, tick Electrical plan and Labels, and export.

Shorter task pages: Draw an electrical plan (placing and naming devices), Outlet and switch combinations, Circuit lines, Upload your own symbols and the floor plan symbols reference.

What you'll need

  • •A floor plan with walls (one room is enough; a template works well)
  • •A computer, tablet or phone: everything here works on all three, and the phone layout differences are noted

In this guide

  1. 1

    What an electrical plan in RoomSketch3D contains

    A finished plan has four layers of information, all drawn over the walls, doors and windows you already have:

    LayerWhat it isWhere it comes from
    Wall devicesOutlets (sockets) and switches, alone or in combinationsSymbols panel, tap a wall
    Room symbolsCeiling, recessed, pendant and track lights, fans, detectors, data and phone jacks, Wi-Fi, cameras, panel, junction box, plumbing and HVAC marksSymbols panel, +Add, then drag
    Circuit linesSolid or dashed runs from device to device, with a name such as Breaker 7Circuit line tool in the Symbols panel
    NamesBreaker numbers or descriptions beside devices and on each circuitThe name box of any device or line

    The example on this page is the Medium 2-Bedroom Apartment template with an electrical plan added in the living room and kitchen: a range outlet (R), a GFCI outlet over the counter, a two-gang switch by the front door (single + dimmer named Living lights), a switch with an outlet below it on the kitchen wall, a double outlet behind the TV, pendants over the island, recessed lights, a ceiling light and a smoke detector. Three circuits: Breaker 7 (dashed) runs the outlets along the walls, Breaker 3 (solid) runs the dimmer to the living-room light around the corner, and Breaker 5 (dashed) runs the kitchen switch to the recessed lights and pendants.

    The example plan: Breaker 7 outlets along the walls, Breaker 3 (solid) to the living-room light, Breaker 5 to the kitchen lights.
  2. 2

    Every electrical symbol you can place

    The Symbols panel holds 69 built-in symbols in three packs. Tabs at the top pick All, US or Europe; it opens on US if you work in feet and inches and on Europe if you work in metres, then remembers your choice. Search filters everything (try gfci, dimmer, schuko, ethernet). Your own uploads sit under My Library at the top.

    PackOutlets / socketsSwitches
    US (27)Single, Duplex, Quad, GFCI, 20A, 240V, Range, Dryer, Weatherproof, Switched, USB, Tamper-Resistant, Isolated Ground, AFCI, Floor OutletSingle, Double, 3-Way, 4-Way, Dimmer, Smart, Pilot Light, Key, Timer, Occupancy Sensor, Weatherproof, Low Voltage
    Europe (14)Earthed, Unearthed, Double, Triple, Switched, Outdoor IP44, USB, 400V 3-PhaseOne-Way, 2-Gang, Two-Way, Intermediate, Dimmer (EU), Push Button

    Shared (28), the same in every region: Ceiling, Recessed, Wall, Pendant, Track and Under-Cabinet lights, Ceiling Fan, Electrical Panel, Smoke Detector, CO Detector, Smoke/CO Detector, Doorbell, Motion Sensor, Junction Box; plumbing (Shut-off Valve, Floor Drain, Hose Bib, Water Heater); HVAC (Thermostat, Supply Vent, Return Vent); telecom (Phone Jack, Data Jack, Wi-Fi Access Point); CCTV Camera; and North Arrow, Marker Dot, Callout Circle.

    Each outlet and switch kind draws its own plan mark, with a short tag where the trade uses one: GFCI, 20A, R (range), D (dryer outlet; on a switch, dimmer), WP, USB, TR, IG, AFCI, 3 and 4 (3-way, 4-way), P (pilot light), K (key), T (timer), OS (occupancy), LV (low voltage), a wireless mark for smart switches, and on European sockets 2, 3, IP44 and 400V. A tile also shows the real plate size (for example 2.75 × 4.5 in for a duplex outlet).

    The Furnish catalog (Indoor → Fixtures) also has six 3D wall devices: Light Switch (3D), Double Light Switch (3D), Dimmer Switch (3D), Duplex Outlet (3D), GFCI Outlet (3D) and USB + Outlet (3D). They place the same way and become the same kind of wall device; the Symbols panel simply has far more kinds. Anything missing can be drawn as a transparent PNG and uploaded: see upload custom symbols.

    Symbols → US: outlet and switch tiles, Upload custom symbol and Circuit line.
  3. 3

    Put outlets and switches on walls

    Outlets and switches are wall devices: tap the tile, tap +Add, and the banner asks you to tap a wall. Tap where the device goes and it sits flush on that wall at its standard height. Add as many as you need. Drag a device along its wall to move it, or onto another wall to move it there. Interior walls have two faces. A device lands on the face you tapped from, so tap from inside the room it serves. To move it to the other face later, use In / Out in its settings. In the example, the double outlet behind the TV sits on the living-room face of the bedroom wall: Out is picked because the tap came from the bedroom side. Devices can't go on a curved wall yet (Doors, windows and outlets can't go on a curved wall yet); put them on a straight wall.

    An interior wall: In / Out picks which room the outlets face.
  4. 4

    Lights, detectors and other room symbols

    Everything that isn't an outlet or switch drops into the room like furniture: tap the tile, tap +Add, and it lands in the middle of the room; drag it to where the fixture is. That covers ceiling, recessed, pendant and track lights, the ceiling fan, detectors, jacks, Wi-Fi, cameras, the electrical panel, junction box, valves, vents and the generic markers. Ceiling items are drawn over whatever is below them (a light over the island is not on the island). Three shared symbols hang on a wall instead: Wall Light, Under-Cabinet Light and Doorbell. Tap a wall to place them; they sit flush on its face and stay on the wall when you drag them. (Wall lights placed before this behaviour existed stay free.) Floor Outlet is a free symbol you can put anywhere, for example under a sofa that floats in the room. Select any room symbol to resize it, colour it, rotate it or rename it. A renamed symbol shows its name on the plan, like a device.

    Room symbols drop at the centre and drag anywhere.
  5. 5

    A device's settings: kind, Mount height, distances, name

    Select an outlet or switch (tap its symbol beside the wall) and its settings card opens: - Name (the first box) starts as Outlet or Switch. Type a breaker number or a description and press Enter. Only a name you typed shows on the plan. - Along wall with two arrow boxes (← → on a wall that runs across the screen, ↑ ↓ on one that runs up and down): the distance along the wall to the nearest wall or opening on each side. Type a number to move the device exactly. - In / Out: which face of the wall it is on. - Kind: a drop-down of every outlet and switch kind in the same pack, so a placed Duplex can become a GFCI, or a switch can become a socket, without placing it again. - Mount: the height of the bottom of the plate above the floor, from 0 to 10 ft. - Add outlet / Add switch: turns the device into a combination (next section). - The red trash can deletes it (so does the round red button by the symbol, or the Delete key). Default Mount heights (bottom of plate): most US outlets 12 in; GFCI 42 in (over a counter); 240V and Weatherproof 18 in; Dryer 30 in; Range 4 in; US switches 46 in (about 48 in to the centre); European sockets 12 in (about 30 cm) and European switches 41 in (about 104 cm). Change any of them per device.

    An outlet's card: name, Along wall, In/Out, kind, Mount, Add outlet / Add switch.
  6. 6

    Outlet and switch combinations

    Real installations group devices at one spot: a two- or three-gang frame of sockets, a light switch with a socket right below it, a row of switches by the door. In RoomSketch3D that is a combination: one spot on the wall holding up to 5 devices, each with its own kind, name and (when stacked) its own height. Two ways to make one: 1. Select a device and tap Add outlet or Add switch. The new device joins the same frame. It starts as a Duplex outlet or a Single switch (on a European device, an Earthed socket or a One-Way switch); change its kind in its row. 2. Drag one outlet or switch onto another. When it is right on top of the other symbol, a blue Drop to combine label appears; let go and they become one combination. A device placed with +Add right on top of an existing one joins it the same way. Both must be on the same face of the same wall, and the drop has to land within about an inch of the other symbol, so two outlets placed side by side stay two outlets. On the plan, each device draws its own symbol inside a thin frame. The combination moves, flips In / Out and deletes as one; circuit lines can end on any single device in it.

    Drag an outlet onto a switch: Drop to combine.
  7. 7

    Combination settings: side by side or stacked, one row per device

    Select a combination and its card lists every device on its own line: number · kind · name · Mount (stacked only) · Separate · Remove. - Layout → Side by side: the devices sit next to each other in one frame at the same height; one Mount box sets the whole frame. - Layout → Stacked: one above the other, each with its own Mount. Because a floor plan can't show height, a stacked combination is drawn outward from the wall, the first device nearest the wall. A new device added to a stacked combination starts one plate (2.8 in, the 71 mm European frame pitch) below the lowest one, or above it when that would go below the floor. - Automatic layout when you drag: two devices at the same height join Side by side; at different heights (a switch dropped on an outlet) they join Stacked and keep both heights. - Name: the first device uses the card's main name box; every other device has its own Name box. The plan shows the names together, separated by a dot (for example Entry · Living lights). - Separate (the broken-link button) takes that device out and places it on its own, 6 in along the same wall. - Remove (its red trash can) deletes just that device. Removing the first one makes the next one the first, and lines on it stay connected. - The trash can at the bottom of the card deletes the whole combination. The example's front-door switch is a side-by-side pair: Switch (Single) and Switch (Dimmer) named Living lights, Mount 3 ft 10 in. The kitchen wall has a stacked Switch (Single) at 3 ft 10 in over an Outlet (Duplex) at 1 ft.

    Stacked: every device gets its own row and its own Mount.
  8. 8

    Side-by-side frames: double switches and multi-gang outlets

    Side by side is the multi-gang box: two or three switches by a door, or a double or triple outlet over a desk or behind a TV. Change each row's kind to say exactly what is in the box (a single switch next to a dimmer, a duplex next to a USB outlet, three Schuko sockets with one USB socket). When should you use a combination rather than one symbol such as Outlet (Quad), Switch (Double) or Socket (Triple)? Use the single symbol when the device really is one part (a two-gang rocker switch, a quad receptacle) and you don't need to tell its halves apart. Use a combination when the parts are different kinds, carry different names or breakers, or connect to different circuit lines. Each device in a combination counts on its own in the legend and the circuit list.

    Add switch made a two-gang frame; the second device is now a dimmer named Living lights.
  9. 9

    Names, breaker numbers and the layer that shows them

    Give each device, room symbol and circuit line a name that a person at the panel can match: Breaker 12, B12 – Kitchen counter, Living lights. Use the same wording everywhere. Two devices on one breaker can share a name. Names, devices, room symbols and circuit lines all show on the plan while Layers → Show outlets, switches & symbols is ticked (Layers is the stacked-sheets button, first in the toolbar above the plan). Untick it while you arrange furniture: everything electrical hides and can't be tapped, but nothing is deleted and the 3D view still shows the outlets and switches. The row switches itself on when you place a device or open a plan that has them, unless you turned it off yourself. The indented Circuit lines row under it hides just the lines, and Show furniture hides the furniture instead (see Plans per trade below). The export dialog's Electrical symbols and Circuit lines boxes start the way these rows are set. On exports, the Labels option prints the names. See electrical plan outlets switches symbols for a breaker-map walkthrough.

    Layers → Show outlets, switches & symbols, with its Circuit lines row: devices, lines and names.
  10. 10

    Draw circuit lines

    A circuit line shows which devices share a feed: a switch and the lights it runs, or the outlets on one breaker. In the Symbols panel tap Circuit line (it changes to Exit circuit line). The hint across the plan reads: Click each symbol to connect them. Click empty space to add a bend. Click the first symbol again to save the line and start another from it · Enter to finish · Esc to cancel (on touch: Tap … · Done to finish · ✕ to cancel). 1. Tap the first device. The first tap has to be a symbol; a tap on empty floor shows Tap a symbol to connect it. 2. Tap the next devices in wiring order. Any symbol works: outlets, switches, one device of a combination, lights, jacks, your own uploads. 3. Press Enter or tap Done. The line gets a name (Circuit 1, Circuit 2 …) and the tool stays on for the next one. Branch (one switch to two lights, a double switch): after the first light, tap the first device again. The line is saved and a new one starts from that device (Line saved. Tap the next symbol to run another line from here). A line attaches to its symbols: move a device and the line follows; delete a device and it comes off its lines (an end takes its piece with it, a middle device's neighbours join up). Lines draw on every export.

    The armed tool and its hint: symbols connect, empty space adds a bend.
  11. 11

    Route a line along the walls with bends

    Straight device-to-device lines cut across the room. Real wiring runs along walls and through ceilings, and an installation plan draws it that way. While drawing, tap an empty spot to add a bend: the line goes from the last device to that point, then on to the next thing you tap. A bend that is close to straight across or straight up and down on your screen (within about 12 degrees) is squared up for you, so right-angle runs come out clean, even on a rotated plan. In the example, Breaker 7 starts at the outlet on the right wall, bends at the corner, and runs along the bottom wall to the outlets at both ends of the sofa. Breaker 3 leaves the dimmer, goes straight up the room, bends, and runs across to the ceiling light. A line always runs from symbol to symbol: you can't end it on a bend. Backspace (or Undo) removes the last point you placed, device or bend.

    One tap in the corner bends the run along both walls.
  12. 12

    Edit a finished line: extend, bend, remove

    Tap a line (or its name) to select it. On the plan: - A blue + past each end (Add to this line): tap it, then tap more symbols (or empty space for bends) and Done. They join the same circuit, name and colour. - A small + in the middle of each stretch that is long enough: drag it to add a bend there. It slides aside so it never hides under a name plate. - Drag a bend to move it; it lines up with the points on either side when it comes close. - Tap a dot or a bend, then the red − (Remove from this line). A bend just goes; a device's dot leaves the device on the plan and takes it off the line. If one device would be left, the line is deleted. - Drag an end dot onto another symbol to re-point that end. The card repeats this: Drag a + in the middle of the line to add a bend, and drag a bend to move it. Tap + at an end to add symbols. Tap a dot or bend to remove it, or drag a dot onto another symbol.

    Selected: + at the ends, dots and bends on the line, and the line's card.
  13. 13

    Name, colour and line style of a circuit

    The selected line's card has its name (type Breaker 3 and press Enter; clearing it puts back Circuit N), Color (blue, red, green, orange, purple, black) and Line: Solid or Dashed (dashed is the default and how every line drawn before November 2026 looks). Delete removes the line, not the devices. A common convention: dashed for switch legs and outlet circuits, solid for a home run to the panel, or one colour per breaker. RoomSketch3D doesn't enforce a meaning; the Circuits list on the export shows each line with its own colour and style next to its name, so the sheet explains itself.

    Breaker 3 set to Solid; Breaker 5 and Breaker 7 stay dashed.
  14. 14

    The settings card: move it, reset it; phones

    On a tablet or computer, the settings of a selected outlet, switch, door, window or circuit line open in the same floating card as furniture settings. It steps aside so it doesn't cover what you selected. Drag it by its top row (the dotted grip) to put it anywhere; Reset then appears and puts it back at the bottom of the plan. It opens where you last left it, for furniture too. On a phone the same settings are a panel along the bottom of the screen; in a combination the kind list there is narrower, so the kind name may be cut short (tap it to see the full list).

    Dragged out of the way: Reset puts it back.
  15. 15

    Right-click shortcuts (mouse)

    With a mouse or trackpad, a right-click on the plan acts on what's under the pointer:

    Right-click onWhat happens
    A room symbol (light, fan, detector, jack, Floor Outlet, your uploads)A menu titled with its name: Edit, Duplicate, Rotate 90°, Lock in place / Unlock, Delete
    An outlet or switch on a wallIt's selected and its settings card opens (no menu); the card has the kind, Mount, Add outlet / Add switch and the trash can
    A circuit lineNo menu of its own: the right-click goes to whatever is under the line (the room menu, or a piece of furniture the line crosses). Tap or click the line to select it and use its card
    Empty floorThe room menu, with Rename room

    On a touch screen a long-press keeps opening the room menu, as before. Lock in place on a light or detector stops it being dragged by accident while you draw circuits around it.

    Right-click a light: its own menu, titled Ceiling Light.
  16. 16

    On a phone

    Everything above works on a phone: the Symbols pill opens the panel, a tap places or selects, dragging a selected device moves it, and Done / ✕ in the circuit hint replace Enter and Esc. A selected device's settings fill the bottom of the screen with the same rows: Along wall, In / Out, Layout, one row per device with Mount, Separate and Remove, and Add outlet / Add switch. Zoom in before dragging one device onto another: the drop has to land right on the other symbol.

    Phone: the same settings in a bottom panel.
  17. 17

    The symbol legend and the circuit list

    Export with Electrical plan ticked and two tables print under the drawing: - Symbol legend: one row per kind of outlet, switch and room symbol on the plan, with its mark and a count. Every device of a combination counts on its own (the example's legend lists Outlet (Duplex) ×5, Switch (Single) ×2, Switch (Dimmer) ×1, Outlet (USB) ×1). - Circuits: one row per circuit line, with a sample of its colour and style (solid or dashed), its name, and the devices on it in run order. A device's own name is used when it has one (Breaker 3 — Living lights, Ceiling Light); devices of the same kind are merged with a count (Breaker 7 — Outlet (Duplex) ×3). Bends aren't devices, so they don't appear. The footer gives the plan's name, overall size, gross and usable area and the date. That is what an electrician needs to price the job: how many of each device and what is on each breaker.

    From a real PNG export: the legend and the circuit list.
  18. 18

    Export, print and CAD: what each one contains

    Open Export / Print / Share → PNG/JPG/PDF or Print. Choose Export (or Print), a Format (PNG, JPG, PDF) and a paper size. Under Options:

    - Electrical plan: hides furniture and room colour fills (Room tints greys out), keeps the walls, doors, windows, room names and sizes, every symbol, light and circuit line, and adds the legend and circuit list. - Labels: prints device and circuit names (and room names). On a phone it starts unticked. - Electrical symbols and Circuit lines: whether the devices and the lines go in the file. They start the way Layers shows them, so a layer you hid on screen starts unticked here. Unticking Electrical symbols takes the lines with it. - Furniture: every piece except the electrical symbols and lights. Greyed out while Electrical plan is ticked. - Black & white for a pure line drawing; Interior / Exterior dimensions, Grid, Elevation views and the rest work as on any export.

    Without Electrical plan, symbols and circuit lines print over the furnished plan (when their boxes are ticked), without the legend.

    OutputWhat you get
    PNG / JPGOne image of the plan with legend and circuit list (checked on a PNG export)
    PDFThe same sheet as a page, for printing or email (checked)
    Print tabThe same sheet sent to your printer (not separately tested)
    DXF (Export / Print / Share → DXF → Export DXF)CAD drawing in inches with an ELECTRICAL layer: each outlet and switch (every device of a combination, side by side) as a circle mark with its tag (GFCI, R, D, USB …), device names, and each circuit as a polyline with its name. Room symbols such as lights export as labelled footprints. No legend table. The DXF always carries everything (no Furniture / Electrical symbols / Circuit lines boxes); switch CAD layers off instead. (Checked on a real DXF.)

    See print your floor plan and export autocad dxf for paper sizes and CAD details.

    Electrical plan + Labels: the sheet an electrician needs.
  19. 19

    The exported electrical plan

    This is the living room and kitchen from the real PNG export of the example. Furniture is gone; the walls, the door swing, the room name and size, every outlet and switch with its tag, the combinations in their frames, the lights and detector, the three named circuits with their bends, and the device name Living lights remain. Hand it to an electrician, attach it to a permit application as a sketch, or tape it inside the panel door.

    The exported sheet: devices, frames, names and routed circuits, no furniture.
  20. 20

    Plans per trade: electrician, symbols only, furniture

    One design can give each trade its own sheet. Nothing is copied or duplicated: you export the same plan several times with different boxes ticked. The boxes live in Export / Print / Share → PNG/JPG/PDF or Print → Options, and they start the way Layers shows the plan, so you can set up the view on screen first.

    SheetWho it's forTickUntick
    Electrician's planThe electrician pricing and wiring the jobElectrical plan, Electrical symbols, Circuit lines, Labels(Furniture greys out by itself)
    Symbols-only planDevice placement, a client sign-off, a permit sketch, a plan before circuits are decidedElectrical plan, Electrical symbols, LabelsCircuit lines
    Furniture planThe client, the furniture installer, the flooring or painting crewFurniture, Labels, Room tints if you want colourElectrical symbols (Circuit lines greys out)
    Empty shell with devices, in colourA walkthrough of outlet positions with the room colours keptElectrical symbols, Circuit linesFurniture (leave Electrical plan off)

    What each one contains, checked on real PNG exports of the example plan:

    - Electrician's plan: walls, doors, windows, room names and sizes, measurements, every outlet, switch, combination and light, the routed circuit lines with their names, the Symbol legend with counts, and the Circuits list. No furniture, no colour fills. - Symbols-only plan: the same without the lines and without the Circuits list (the legend stays). Named devices keep their names. - Furniture plan: the furnished plan with room colours and no outlets, switches, lights or circuit lines.

    To set it up on screen, use Layers: Show furniture off gives the electrician's view while you draw circuits, Circuit lines off (indented under Show outlets, switches & symbols) gives the symbols-only view, and Show outlets, switches & symbols off gives the furniture view. Open the export dialog afterwards and the boxes already match. Export each sheet as PNG or PDF; repeat for each floor.

    The Options for each sheet: electrician, symbols only, furniture plan.
  21. 21

    The three plans side by side

    The kitchen and living room of the example from the three real exports. Top: the electrician's plan, with Breaker 5 (green, dashed) routed from the kitchen switch around the recessed lights to the pendants, Breaker 3 (red, solid) from the dimmer to the ceiling light, and Breaker 7 (blue, dashed) along the outlets. Middle: symbols only: the same devices and names, no lines. Bottom: the furniture plan, with the island, kitchen run, sofa, rug and TV console and no electrical marks. Send the electrician the top sheet (plus the cable list below), the client or an inspector the middle one when only positions matter, and everyone else the bottom one. If a sheet should show the furniture faintly under the electrics, export without Electrical plan and keep Furniture ticked: symbols and lines print over the furnished plan.

    Top to bottom: electrician, symbols only, furniture plan, all from one design.
  22. 22

    The cable list: length of every run, in Excel

    On a computer, Export / Print / Share → Schedules (Excel) → Cable runs turns your circuit lines into a cable pull list. Each line is split at every device it connects, and each stretch is one row: Circuit (its name, such as Breaker 5), Run (1, 2, 3 … in drawing order), From and From room, To and To room, and Length along the line with every bend included, in inches or centimetres. Download CSV saves that table; Download all (Excel) saves one .xlsx with the Rooms, Items by room and Cable runs sheets. In the example, Breaker 5 gives four runs: 72.1 in (switch to the first recessed light, around the corner), 65 in, 71 in and 24 in, 232.1 in or about 19 ft 4 in in all. Total any circuit in Excel with =SUMIF(A:A,"Breaker 5",G:G) or a PivotTable. Route the lines the way the cable goes, because the length is the drawn path. The length is measured on the plan, so it doesn't include the drops from the ceiling or floor to each box (work them out from each device's Mount and your ceiling height), the run to the panel unless you drew one to an Electrical Panel symbol, or slack. The Items by room sheet counts every outlet, switch and light per room. Phones and the apps don't have Schedules yet; there, the Electrical plan export's Circuits list names the devices on each circuit, without lengths. Full details: schedules room list and cable list.

    Schedules → Cable runs: one row per stretch between two devices, length along the line.
  23. 23

    Outlets and switches in 3D

    In the 3D view, outlets and switches appear on their walls at their Mount heights, drawn at real plate size (slightly enlarged so you can find them): US receptacles and toggles, Decora-style GFCI and AFCI, European 80 mm frames with Schuko sockets and rockers. A combination shows as one multi-gang plate or frame with each device in its own slot: side by side in a row, or one above the other at each device's height. Floor Outlet also shows in 3D. Other plan symbols (lights, detectors, jacks, vents, uploads) are 2D only; for lights you can see in 3D, add fixtures from the Indoor catalog (for example the flush ceiling or pendant lights). Turn on Dollhouse and High quality to look at one wall closely.

    In 3D, left to right: US duplex + USB, US three-gang switch (single, dimmer, 3-way), European switch over socket, European triple socket with USB.
  24. 24

    Drawing a German or European plan

    Pick Europe in the Symbols panel for IEC-style marks: a half-circle socket on a short stem, earthed sockets with the extra bar, 2 / 3 for multiple sockets, IP44 outdoors, 400V for three-phase, and switches as a small circle with one or two strokes. The kind list of a European device offers European kinds only, so a German plan stays consistent. German plans usually show Kombinationen: a switch with a socket under it beside the door, and two- or three-gang socket frames over desks and worktops. Make them as combinations (drag one onto the other, or Add outlet / Add switch). A switch dragged onto a socket keeps both heights and stacks; Add outlet on a stacked switch puts the socket one 71 mm frame below it. Heights in Germany: DIN 18015-3 recommends 105 cm above the finished floor for switches and sockets in the middle zone and 30 cm in the lower zone, and keeps cable runs in installation zones (horizontal bands 15–45 cm below the ceiling, 100–130 cm and 15–45 cm above the floor; vertical bands 10–30 cm beside doors, windows and corners) so nobody drills into a hidden cable. RoomSketch3D's Mount is the bottom of the plate: for a box centred at 105 cm, type about 101 cm (half an 80 mm frame lower); for 30 cm, about 26 cm. Check the heights your electrician uses; the standard gives preferred heights, and kitchen worktop sockets are set by the worktop.

    One wall, both packs: US combinations (left), European combinations (right).
  25. 25

    European combinations, row by row

    A German entry combination: Switch (One-Way) at Mount 3 ft 5 in (about 104 cm) with Socket (Earthed) below it at 3 ft 2.2 in, Stacked. A worktop frame: Socket (Earthed), Socket (Earthed) and Socket (USB) side by side, one Mount for the frame. Units follow your settings, so in metres the boxes read in centimetres.

    Schalter-Steckdosen-Kombination: one-way switch over an earthed socket.
  26. 26

    US placement rules to check your plan against

    RoomSketch3D draws what you place; it doesn't check code. These are the rules most US electrical plans are checked against (2021 International Residential Code, Chapter 39, which follows the National Electrical Code, NEC 210.52 for receptacle spacing). Local amendments vary, and the inspector and your electrician have the final word.

    WhereRuleSection
    Any wall in a living areaNo point along the floor line more than 6 ft from an outlet (the "12-ft rule": outlets at most 12 ft apart). Walls 2 ft or wider countIRC E3901.2.1, E3901.2.2
    Kitchen counterEvery counter space 12 in or wider; no point along the wall line more than 24 in from an outlet (about every 4 ft)E3901.4.1
    Island / peninsulaOne outlet for the first 9 sq ft of counter, plus one per extra 18 sq ft; a peninsula needs one within 2 ft of its endE3901.4.2
    Counter outlet heightOn the counter or up to 20 in above itE3901.4.3
    BathroomOne within 36 in of each basin's outside edgeE3901.6
    OutdoorsOne at the front and back, no higher than 6 ft 6 in above gradeE3901.7
    Foyer over 60 sq ftAn outlet in each wall space 3 ft or widerE3901.11
    GFCIBathrooms, garages, outdoors, crawl spaces, basements, kitchen counters, within 6 ft of a sink or tub, laundry areas and moreE3902
    AFCICircuits in kitchens, living and family rooms, dining rooms, bedrooms, closets, hallways, laundry areas and similar roomsE3902.20
    Tamper-resistant15 A and 20 A, 125 V and 250 V receptacles in a homeE4002.14
    Switched lightA wall-switch-controlled light in every habitable room, kitchen and bathroom; stairs with 6 or more risers get a switch at each levelE3903.2, E3903.3.1
    Switch height limitHandle no higher than 6 ft 7 inE4001.6

    Outlets more than 5.5 ft above the floor don't count toward the spacing rule (E3901.1).

    Heights are mostly custom, not code. The code sets no height for an ordinary outlet. Common practice is 12–18 in to the bottom or centre of an outlet, about 42–44 in for counter outlets (above a 36 in counter and backsplash), and 44–48 in to the centre of a switch. For accessible design, the 2010 ADA Standards put operable parts between 15 in and 48 in above the floor (308.2.1, 308.3.1).

    In RoomSketch3D: use the tags (GFCI, AFCI, TR, WP) to show protection, the Along wall boxes to check the 12-ft and 24-in spacing, and Mount for heights.

    Along wall shows the gap to the next wall or opening on each side: useful for the 6-ft rule.
  27. 27

    Keyboard shortcuts and undo

    KeyWhile drawing a circuitOtherwise
    EnterFinish the lineConfirms a typed name or number
    EscCancel the draft (press again to leave the tool)Deselect
    BackspaceRemove the last point (device or bend)Delete the selected item
    Delete—Delete the selected item
    Ctrl/Cmd + Z, Shift + Ctrl/Cmd + ZStep the draft back / forwardUndo / redo any change, including combining, separating and line edits

    On touch, use Done and ✕ in the hint bar and the Undo / Redo arrows in the toolbar. See keyboard shortcuts and undo redo.

  28. 28

    What it can't do yet, and the workaround

    You wantTodayWorkaround
    A code check (spacing, GFCI, loads)Not available; nothing is validatedCheck against the rules above with the Along wall boxes and tags; your electrician sizes circuits and wire
    A panel schedule with breaker sizes and wire gaugesThe Circuits list names lines and devices; Schedules gives run lengthsPut the size in the name: Breaker 12 – 20A kitchen
    Cable lengths with the drops to each boxSchedules → Cable runs measures along the plan onlyAdd each drop from the device's Mount and the ceiling height, plus the run to the panel and slack
    A cable list on a phoneSchedules is on a computer onlyOpen the design on a computer; on the phone, the Electrical plan export's Circuits list names the devices per circuit
    Several trade sheets in one exportOne sheet per exportExport once per trade with different Options boxes (see Plans per trade)
    Trade layers in the DXFThe DXF always carries everythingTurn CAD layers off; electrics are on the ELECTRICAL layer
    A right-click menu on a circuit lineNot yet; the right-click goes to what's under itClick the line to select it and use its card
    Curved switch legsLines are straight segmentsAdd bends to route the line; dashed reads as a switch leg
    Lights, fans, jacks in 3DOnly outlets, switches and the Floor Outlet show in 3DAdd catalog light fixtures from Indoor for the 3D view
    A combination of lights, data jacks or room symbolsCombinations are for outlets and switchesPlace the symbols next to each other and give them the same name
    More than 5 devices at one spotUp to 5Two combinations side by side
    US and European kinds in one combinationThe kind list keeps one packPick one pack for the whole plan (mixing confuses installers anyway)
    An outlet on a curved wallNot yetStraighten that stretch or use the nearest straight wall
    A symbol that isn't in the libraryNot built inDraw it as a transparent PNG: upload custom symbols

Tips

Place furniture first, then devices

Outlets follow the furniture: one each side of a bed, behind the TV, at the desk, where the sofa won't block it. Switches follow the doors: inside the room on the latch side.

One name per breaker

Name the circuit line and every device on it the same way (Breaker 7). The export's circuit list then reads exactly like the labels in your panel.

Route lines, don't cross rooms

Tap the corners while you draw. Runs along walls are easier to read and closer to how cable really goes; a near-straight bend squares itself.

Hide the electrics while you furnish

Untick Layers → Show outlets, switches & symbols to move furniture without grabbing a device; tick it again for the electrical pass.

Hide the furniture while you wire

Untick Layers → Show furniture: outlets, lights and circuits stay, and a tap can't grab a sofa or a rug by mistake while you draw lines.

Set Layers before you export

The export's Furniture, Electrical symbols and Circuit lines boxes start the way Layers shows the plan, so what you see is what you get. Glance at the boxes anyway.

Use the tags as notes

A GFCI, AFCI, TR or WP tag tells the installer the protection you expect at that spot, without a separate note.

Zoom in to combine

The drop has to land on the other symbol (within about an inch on the wall). Zooming in makes it easy on a phone and prevents accidental combining.

Common confusions

Reading Mount as the centre height

Mount is the height of the bottom of the plate. A switch "at 48 in" to its centre has a Mount of about 46 in; a German socket at 105 cm centre is about 101 cm.

Tapping empty floor first

A circuit line has to start on a symbol. Tap a device first; after that, empty space adds bends.

Tapping the first device to finish

That saves the line and starts a new branch from it. Finish with Enter or Done.

Dropping a device near another and expecting it to combine

Combining needs the drop right on the other symbol, on the same face of the same wall. A device on the other face (In / Out) never combines; flip one first.

Deleting a device to take it off a line

Select the line, tap the device's dot and use the red − instead. Deleting removes the device from the plan.

Exporting with furniture and no legend

Without Electrical plan ticked, there is no legend or circuit list and the furniture hides the symbols.

A layer hidden on screen goes missing from the file

The export boxes start from Layers. If you hid outlets or circuit lines while furnishing, the dialog opens with Electrical symbols or Circuit lines unticked; tick them for the electrician's sheet.

Ordering cable from the plan lengths alone

Schedules measures along the plan. Add the vertical drops, the run to the panel and slack before you order.

Frequently asked questions

Can RoomSketch3D draw an electrical circuit diagram on a floor plan?

Yes. Place outlets, switches and lights with the Symbols panel, then use Circuit line to connect them in wiring order, with bends to route along the walls. Each line can be named after its breaker, coloured and set solid or dashed, and the Electrical plan export lists every circuit with its devices. It is a layout diagram on the floor plan, not a single-line schematic or a load calculation.

How do I put two outlets or an outlet and a switch in one box?

Select one device and tap Add outlet or Add switch, or drag one device onto the other until Drop to combine appears. Choose Side by side for a multi-gang frame or Stacked for one above the other. See outlet and switch combinations.

How do I make a circuit line follow the walls?

While drawing, tap empty spots where the line should turn. Each tap adds a bend, squared up when it is close to horizontal or vertical. On a finished line, drag the small + in the middle of a stretch to add a bend, or drag an existing bend.

Can I make circuit lines solid instead of dashed?

Yes. Select the line and pick Line → Solid in its card. Dashed is the default.

What height do outlets and switches get?

Mount (the bottom of the plate) defaults to 12 in for most US outlets, 42 in for GFCI, 18 in for 240V and weatherproof, 30 in for a dryer outlet, 4 in for a range outlet and 46 in for US switches; European sockets 12 in (about 30 cm) and switches 41 in (about 104 cm). Change it per device in the Mount box.

Do outlet and switch combinations print and export?

Yes. PNG, JPG and PDF draw each device's symbol in a thin frame, the legend and circuit list count every device, the 3D view shows one plate per device, and the DXF draws each device side by side on the ELECTRICAL layer. (PNG, PDF and DXF were checked on real exports.)

Does the DXF export include outlets, switches and circuits?

Yes, on a layer called ELECTRICAL: each outlet and switch as a circle mark with its tag, device names, and each circuit line as a polyline with its name. Lights and other room symbols export as labelled footprints. There is no legend table in the DXF.

Can I draw a German electrical plan (Elektroplan)?

Yes. Choose the Europe pack for IEC-style sockets and switches, build Schalter-Steckdosen combinations with Add outlet / Add switch, set Mount heights in centimetres if you work in metric, and route lines along the walls. DIN 18015-3 recommends 105 cm and 30 cm above the finished floor; type about 101 cm and 26 cm in Mount, since Mount is the bottom of the plate.

Why don't my lights show in 3D?

Plan symbols other than outlets, switches and the Floor Outlet are 2D marks. Add light fixtures from the Indoor catalog if you want to see them in 3D.

My outlets and lines disappeared. Are they deleted?

No. Tick Layers → Show outlets, switches & symbols (and its Circuit lines row for the lines). While they are off, the devices or lines are hidden from the plan, and the export dialog opens with Electrical symbols or Circuit lines unticked; the 3D view still shows the outlets and switches.

How do I give the electrician a plan without furniture?

Export / Print / Share → PNG/JPG/PDF or Print, tick Electrical plan and keep Electrical symbols, Circuit lines and Labels ticked. Furniture and colour fills are left out, and the legend and circuit list are added. For the furniture-only plan, untick Electrical symbols instead.

Can I export the outlets and switches without the circuit lines?

Yes. Untick Circuit lines in the export Options (or untick Layers → Circuit lines first). Keep Electrical plan ticked for a symbols-only sheet with the legend.

How much cable does each circuit need?

On a computer, Export / Print / Share → Schedules (Excel) → Cable runs lists every run between two devices with its length along the line, bends included. Total a circuit in Excel, then add the drops to each box, the run to the panel and slack. See schedules room list and cable list.

Is there a right-click menu for outlets and circuit lines?

With a mouse, right-clicking a light or other room symbol opens its menu (Edit, Duplicate, Rotate 90°, Lock in place, Delete). Right-clicking an outlet or switch selects it and opens its card. Circuit lines have no right-click menu yet: click the line to select it.

Does RoomSketch3D check my plan against the electrical code?

No. It draws what you place. Use the rules on this page to check spacing and protection, and have a licensed electrician and your local building department confirm it.

Sources

Start designing your room

Put this into practice in the floor planner: draw it, furnish it, walk through it in 3D — on web, iOS, and Android.

Open RoomSketch3D

One-time purchase · No subscription · Web, iOS & Android